LORD® Products
lord-products
Chemlok® 459X primer can be used in conjunction with urethane and epoxy adhesives, as well as with a variety of double-sided tapes. It may also serve as a primer to enhance the adhesion of polyurethane coatings on cured EPDM and other difficult-to-bond elastomers. /Asset/459X.jpg
LORD® 7701 adhesion enhancer/surface modifier is used in conjunction with a broad range of LORD® adhesives, including epoxy and urethane adhesives, for bonding cured rubber. It improves adhesion to a variety of cured and thermoplastic polymeric materials, including natural rubber, synthetic polyisoprene, SBR, butyl, polybutadiene, neoprene, EPDM, nitrile, polyurethane, styrene-butadiene block copolymers, styrene isoprene rubbers and polyvinyl chloride. /Asset/7701.jpg
LORD® 506 acrylic adhesive can be mixed with either LORD Accelerator 4, LORD® Accelerator 17 or LORD® Accelerator 19. LORD Accelerator 4 is a no-mix accelerator applied to the substrate before the acrylic adhesive. LORD® Accelerators 17 and 19 must be mixed into the acrylic adhesive prior to application. LORD® Accelerator 19 is available in off-white or black. For further detailed information on LORD® Accelerator 4, LORD® Accelerator 17 and LORD® Accelerator 19, refer to the applicable data sheet. /Asset/506.jpg
LORD® Maxlok™ acrylic adhesives are available in a range of working times to accommodate a wide variety of process requirements. /Asset/Maxlok.jpg
LORD® Accelerator 20GB allows precise control of the adhesive bondline thickness due to its content of glass beads. For further detailed information, refer to the LORD® Accelerator 20GB data sheet. /Asset/LORD-810_20.jpg
LORD® 403, 406 and 410 Acrylic Adhesives with LORD® Accelerator 19 or 19GB
(3) LORD® 403, 406 and 410 acrylic adhesives in combination with LORD® Accelerator 19 or 19GB can be used to replace welding, brazing, riveting and other mechanical fastening methods. These adhesives perform particularly well in low-temperature environments and applications that are subject to high impact or high peel loads. LORD® 403, 406 and 410 acrylic adhesives provide a range of working times to accommodate a wide variety of process requirements. /Asset/Lord-406.jpg Chemlok® 459X Chemical Primers
LORD® Chemlok® 459X primer is designed for promoting adhesion to thermoplastic elastomers (TPE), thermoplastic polyolefins (TPO) and EPDM. Chemlok® 459X primer is in xylene solvent, diluted for direct application.Chemlok® 459X primer can be used in conjunction with urethane and epoxy adhesives, as well as with a variety of double-sided tapes. It may also serve as a primer to enhance the adhesion of polyurethane coatings on cured EPDM and other difficult-to-bond elastomers. /Asset/459X.jpg
LORD® 7701 Adhesion Enhancer/Surface Modifiers
LORD® 7701 adhesion enhancer/surface modifier is a solvent-based surface treatment for use on various vulcanized and thermoplastic polymeric materials. LORD® 7701 adhesion enhancer/surface modifier chemically alters the surface of the rubber, making it more receptive to bonding.LORD® 7701 adhesion enhancer/surface modifier is used in conjunction with a broad range of LORD® adhesives, including epoxy and urethane adhesives, for bonding cured rubber. It improves adhesion to a variety of cured and thermoplastic polymeric materials, including natural rubber, synthetic polyisoprene, SBR, butyl, polybutadiene, neoprene, EPDM, nitrile, polyurethane, styrene-butadiene block copolymers, styrene isoprene rubbers and polyvinyl chloride. /Asset/7701.jpg
LORD® 305 Epoxy Adhesives with Hardeners
(2) LORD® 305 adhesive is a general purpose, medium viscosity, two-component epoxy adhesive system used for applications that require strong, durable, chemically and environmentally resistant bonds. This adhesive system provides excellent adhesion to prepared metals, fiberglass reinforced plastics (FRP), phenolic, wood, prepared rubber and other materials. It is also used to bond cured rubber to itself and rubber to metal, including gaskets, bushings, shock-absorbing devices and rubber rolls. LORD® 305 adhesive can be either room temperature cured or heat cured for faster processing. /Asset/Lord-305.jpg LORD® 320/322 Epoxy Adhesives with Hardeners
(2) LORD® 320/322 adhesive is a general purpose, twocomponent epoxy adhesive system formulated for primerless adhesion to automotive sheet molded compounds (SMC). This adhesive system also provides excellent adhesion to prepared metals, rubber, fiberglass reinforced plastics (FRP), polyester thermosets and thermoplastics, and many other materials. LORD 320/322 adhesive can be either room temperature cured or heat cured for faster processing. /Asset/Lord-320-322.jpg LORD® 7542 Urethane Adhesives
(5) LORD® 7542 adhesive is an equal-mix, two-component urethane adhesive system used to bond FRP, SMC and other plastics with little surface preparation. This adhesive will also bond primed metals. LORD® 7542 adhesive system is available in a range of working times to accommodate a wide variety of process requirements. /Asset/7542.jpg LORD® 506 Acrylic Adhesives with Accelerator 4, 17 or 19
LORD® 506 acrylic adhesive when cured with LORD® Accelerator 4, 17 or 19 creates a semi-flexible adhesive system that will quickly bond a wide variety of thermoplastics and thermoset plastics.LORD® 506 acrylic adhesive can be mixed with either LORD Accelerator 4, LORD® Accelerator 17 or LORD® Accelerator 19. LORD Accelerator 4 is a no-mix accelerator applied to the substrate before the acrylic adhesive. LORD® Accelerators 17 and 19 must be mixed into the acrylic adhesive prior to application. LORD® Accelerator 19 is available in off-white or black. For further detailed information on LORD® Accelerator 4, LORD® Accelerator 17 and LORD® Accelerator 19, refer to the applicable data sheet. /Asset/506.jpg
LORD® 7550 Urethane Adhesives
(2) LORD® 7550 adhesive is an equal-mix, two-component clear urethane adhesive system used to bond Lexan®, ABS, polycarbonate and other plastics. This adhesive will also bond primed metals. /Asset/lord-7550.jpg LORD® AP-134 Adhesion Enhancer/Surface Modifiers
LORD® AP-134 adhesion enhancer/surface modifier is a one-coat, moisture-cure primer used to promote adhesion to a variety of polar substrates. These substrates include architectural and automotive glass, steel, aluminum, brass, e-coated metal, glass fabric, ceramic tile, vitrified clay pipe, concrete and some plastics. /Asset/ap-134.jpg LORD® Maxlok™ MX/T3, MX/T6 and MX/T18 Acrylic Adhesives
(4) LORD® Maxlok™ MX/T3, MX/T6 and MX/T18 acrylic adhesives replace welding, brazing, riveting and other mechanical fastening methods especially over a wide range of temperature environments subject to high impact or high peel loads.LORD® Maxlok™ acrylic adhesives are available in a range of working times to accommodate a wide variety of process requirements. /Asset/Maxlok.jpg
LORD® 7610DTM Direct-to-Metal Adhesives
LORD® 7610DTM direct-to-metal adhesive/sealant is a single-component, moisture-cure product offering excellent adhesion to various substrates including many plastics, glass, concrete, wood and metals, especially precoated metals /Asset/LORD7610.jpg LORD® 810 Low Read-Through (LRT) Acrylic Adhesives with LORD® Accelerator 20GB
LORD® 810 Low Read-Through (LRT) acrylic adhesive when cured with LORD® Accelerator 20GB creates a flexible adhesive system for bonding metals, such as aluminum, galvanized steel and CRS, and engineered plastics, such as PC-ABS. LORD® 810 adhesive in combination with LORD® Accelerator 20GB delivers fast cure speed and strong bonding with minimal bondline read through (BLRT).LORD® Accelerator 20GB allows precise control of the adhesive bondline thickness due to its content of glass beads. For further detailed information, refer to the LORD® Accelerator 20GB data sheet. /Asset/LORD-810_20.jpg
LORD® 850 and 852 Toughened Structural Acrylic Adhesives with LORD® Accelerator 25GB
(2) LORD® 850 and 852 acrylic adhesives in combination with LORD Accelerator 25GB can be used to replace welding, brazing, riveting and other mechanical fastening methods. These toughened structural adhesives perform particularly well in low-temperature environments and applications that are subject to high impact, high peel loads or high fatigue. LORD® 850 and 852 adhesives provide a range of working times to accommodate a wide variety of process requirements.. /Asset/lord-850.jpg LORD® 7545 Urethane Adhesives
(7) LORD® 7545 adhesive is an equal-mix, two-component urethane adhesive system used to bond FRP, SMC and other plastics with little surface preparation. This adhesive also bonds primed metals and various combinations of dissimilar substrates. LORD® 7545 adhesive system is available in a range of working times to accommodate a wide variety of process requirements. /Asset/7545.jpg 